详细说明
Product Name: Veze Automatic Doors Reflective Type Infrared Sensor Customized: Customized Certification: CE IP Rating: IP54 Material: ABS Production Process: Integration Output Signal Type: Digital Type Detection Type: Infrared Trademark: VEZE Transport Package: Wooden Carton/Case Specification: CE Origin: Ningbo Zhejiang, China HS Code: 90330000 Product Description Automatic Doors Infrared SensorProximity detectorTwo colors optional: black or silver typeSpecificationRay TypeReflect InfrareQuantity of Ray8 emit rays and 8 receive raysThe Function TypeDetect moving thing (people)Max. Installing Height3000mmSensitivity AdjustingSensitivity fine-tuningAdjustment of Detect AreaAdjusting detector angle 0~10Adjusting by DIP switchPowerAC/DC12-36V±5%Consumption CapacityLess than 2.5VARelay OutputDC50V,0.1AOutput Maintaining Time2sIndication of OutputStandby with green light, signal receive with red lightAMB/ENT Temperature-20ºC~+60ºCWeight400gColorSilverAccessoriesSoft cable 2..5m, mounting screws 2 pieces, installing paper, manual instructionName of the PartsDecoration Cover: Indicator, LensUnderframe: Installing Hole, Thread HoleMain Board Detector: Detector Turner, Dip Switch Selection, Distance Near-far Adjust Flap, Sensitivity Fine-TuningAccessoriesInstalling Parer, Connection Cable, Mounting Screws, Manual InstructionNotice of Installing1.Please install within 3m, or the delection sensibility will be reduced.2.Please don't put things such as curtain, flowers and trees which are easy to swing at the delecting area, other- wise will cause the error movement.3.Please don't put in place where is invaded by vapor or oil fog. Otherwise it may cause error action.4.Though the product has anti-interference function. In case in the nearby area more than 3 sets need to be installed, it may occur error action due to the interference. So please ensure the right installing place or ask us for inquiry.5.Please don't put it in place where the reflecting light such as sun light could reach the detecting lense, otherwise it may cause error action. The back ground materials are marble and aluminum etc.Installing Way1.Stick installing paper on the mounting position, according to the instruction on the paper to drill the mounting hole 3.5mm and cable entrance hole.2.Fix the underframe on the wall will two screws.3.Fix the main detector on the underframe4.Connect the microwave sensor and autodoor connector. The gray cable is for power supply. The yellow cable is for signal contact. Neither of them are polarized.5.Keep the connect cable hidden.6.Recover the outer cover after all parameters be set.Near-far Detection Range AdjustmentWhen the detector has been adjusted to max oblique, and the near-far flap adjust to "5" calibration, the detect distance is the maximum.When the detector has been adjusted to vertical, and the near-far flap adjust to"1" calibration. The detect distance is the maximum.Setting the Detector SensitivitySensitivity fine-tuning to adjust the detection sensibility.H: High Sensibility; L: Low SensibilityInput and OutlineYellow Line: Relay Output ( COM NO )Gray Line: Power in ( AC/DC12-36V )Common FaultPhnomenaCauseHandlingNo ActionNo connection for cablePlease ensure the cable has been connectedPower or voltagePlease use the standard power (AC/DC12-36V)Sometimes Does Not WorkDetection lense was polluted by the dust or water drop. So that detection sensibility reduced.Clean with soft fabric and adjust the sensibility fine-tunning to HDetection range is not properAdjust oblique of the detector bodySwinging thing within the detection rangeAdjust the detection range or move away the swinging thing.Error ActionMoving the people within the detection rangePlease re-adjust the DIP switch, or adjusst the oblique of the detector body.Too sensitiveAdjust the DIP AWITCH to ON position and adjust the sensibility fine-tuning to L positionPicture of Automatic Doors Reflective Type Infrared SensorOther Automatic Doors Accessories1. OperationThe automatic door operator is to be fully electronic operator, housed in a fully anodised aluminum transom section.2.ControllerThe intelliget controller unit can be programmed for connection to any security/alarm systems, is self monitoring and calibrating, has memory for all data on door stoke and brake positions.3.UPSThe operator has built-in uninterrupted power supply (Battery back up) operation and security during power failure.4.Belt DriveDrive is by way of toothed belt, which is reinforced with fiberglass tensile members, and has nylon facing surface for tooth protection on the pulleys. This combination produces silent accurate operation.5.TrackingThe track is self-cleaning duel linear. The upper track is made of harder stronger alloy 6351T6, and can be replaced without moving the transom. The wheel trolley is fitted with anti-rise wheels, resulting in very firmly fitted doors with operation free of any racking.6.LockingElectromechanical Locking: An electric lock option is available to give total security and can be adapted where manual locking cannot be achieved, i. E. frameless toughened Glass doors. Lock is the microprocessor controlled electric locking system. The microprocessor monitors all aspects of the lock functions. E. G. To ensure the door is fully closed when the lock is 100% engaged. Terminal outputs are available to signal to security system both door positions and lock status.
