详细说明
Product Name: M20*1.5 Process Connection Pressure Switch Model NO.: YTK-18H IP Rating: IP65 Measuring Medium: Liquid Wiring Type: Three-Wire Thread Type: M Material: metal Production Process: Normal Wirewound Output Signal Type: Analog Type For: Strain Gauge Pressure Transmitter Component: Mechanical Structure Type Type: Capacitive Pressure Sensor Contact Capillary: AC 220V 6A Ambient Temp.: -20-40 Degree Medium Temp.: 0-100 Degree Trademark: TIAN XIANG Transport Package: Box Specification: GB Origin: China HS Code: 9026209090 Product Description YTK-18H High Pressure SwitchesHigh working prssure up to 400bar.Proof pressure can be 600bar.Piston and diaphragm combination sensor, ideal for compact air, light fuel, lubric.YTK-18H Dead Band Non-adjustableSet Point Adjustable Range MpaDead Band No Greater ThanMax. allowable Pressure MpaSwitching frequency Time/min.Material of SensorConnection (F)Weight KgOrder Content NoSet Point Range Lower Limit MpaSet Point Rang Upper Limit MpaShellDiphragmPistonTypicalExplosion-proof Type0.03...40.50.93020Brassfluorine-rubberSteelM20x1.50.8091650009565800.5...6.30.61.3091660009566800.5...100.61.6091670009567800.5...160.71.9091680009568801…...2512.530091691909569891…...401.22.86009169000956980YTK-18H Dead Band AdjustableSet Point Adjustable Range MpaDead Band No Greater ThanMax. allowable Pressure MpaSwitching frequency Time/min.Material of SensorConnection (F)Weight KgOrder Content NoSet Point Range Lower Limit MpaSet Point Rang Upper Limit MpaShellDiphragmPistonTypicalExplosion-proof Type0.03...40.8….2.51.3…2.53020Brassfluorine-rubberSteelM20x1.50.85090650009465800.5...6.31….41.6…4090660009466800.5...101.1…81.6…8090970009467800.5...161.3…122.2…12090980009468801…...251.4…122.8…1230090691909469891…...402…304…306009069000946980YTK-18H Dead Band Adjustable (Narrow Dead Band)Set Point Adjustable Range MpaDead Band No Greater ThanMax. allowable Pressure MpaSwitching frequency Time/min.Material of SensorConnection (F)Weight KgOrder Content NoSet Point Range Lower Limit MpaSet Point Rang Upper Limit MpaShellDiphragmPiston0.03...40.30.83020Brassfluorine-rubberSteelM20x1.50.809165070.5...6.30.41.209166070.5...100.41.409167070.5...160.51.609168071…...250.51.23009169171…...400.71.8600916907Example: choose order content No.0916700 product, a contact signal is required to be generated when pressure raises to 5Mpa( the Increasing Set Point). The steps listed as the following: 1.1 Loosen the locknut, before setting, please screw the product into the threaded connection of test desk, simulate the real working condition to exert pressure on to the product 2 minutes. A spanner must be used to clamp the plane part of the sensor, in order to avoid the countermovement between the shell and the sensor. 1.2 Open the cover, put the cable through the electrical connection into the terminal board, the other end to be linked with multimeter. 1.3. Add pressure to 5Mpa, the value can be read from the standard menometer. 1.4. Clockwise rotate the Set Point Adjusting Bolt, the Set Point value will become biger, until the contact points switches at 5Mpa. 1.5. Tighten the locknut, and regulate the pressure of the testing desk to be arround at 5Mpa, to check if it switches at the 5Mpa when pressure rises. This is just the Increasing Set Point. The correspoding Decreasing Set Point should be 5Mpa minus the Dead Band 1.1Mpa(approximately), thus to be 3.9Mpa(approximately).
