1000liter Retort Sterilizer Water Spray Sterilizer

Product Name: 1000liter Retort Sterilizer Water Spray Sterilizer Model NO.: water spray sterilizer Type: High Voltage Electric Field Sterilization Equipment Property: Food and Beverage Sterilization Energy: Heat Sterilization Operation: Intermittent Structure: Horizontal Principle: Back Pressure Automation: Manually Scale: Small Certification: SGS, CE Customized: Customized Max Working Pressure: 0.35MPa Max Working Temperature: 125 Degree C Construction Material: Stainless Steel Insulation Wall: Optional Trademark: Ranking Transport Package: Wooden Case Specification: small scale sterilizer Origin: China HS Code: 8479 Product Description 1000Liter retort sterilizer water spray sterilizerAUTOCLAVE USER GUIDEGENERAL PROCEDURES1. Room door must be kept closed and locked always.2. Sign up in the log for runs in advance. The log entry should clearly mark the time needed, and should include the user's full name, lab room number, and phone extension.3. Spills must be reported and cleaned up immediately. Get help for this (see 9).4. ALL materials to be autoclaved must be placed in containment trays before being loaded into the chamber.5. Finished material should be removed as soon as possible when acycle ends.6. Autoclave door should not be opened until the chamber temperature falls below 100 degrees Centigrade.7. Never use excessive force when sealing or opening the chamber door.8. The red ON/OFF button should be out (in the OFF position) both before and after each run. Be sure it is OFF before you try to seal the door at the of arun, and before you open the door at the end of arun.9. When problems arise: contact Tonny Cheng,STARTING ARUN1. Inspect chamber before loading. If there is aspill in the chamber, do not use the machine -report the spill immediately. Leave anote ("spill in chamber, DO NOT USE") on the machine.2. Check the jacket pressure -should be approximately 20psi (12 o'clock on the lower gauge).3. Load your material. Select cycle type with pushbuttons. Set sterilize time (and dry time, if running adry cycle). Check that red ON/OFF button is out (the OFF position) -if necessary, push to pop it out.4. Seal the chamber door. Tighten securely but DO NOT OVERTIGHTEN.5. Push the red ON/OFF button in.6. WAIT AND WATCH until the chamber temperature (green arrow) approaches the setpoint (~120C). If steam shoots out from any part of the chamber door (or any other part of the machine other than the drain pipes), push the red ON/OFF button immediately so it pops out to the OFF position. If the steam was leaking from the edge of the door, wait for the chamber to cool below 100C, then you may try to reseal the door. If the problem persists leave the machine off and report the problem. If the steam was leaking from near the center of the door (around the locking mechanism), leave the machine off and report the problem.7. Leave room door locked during the run.ENDING ARUN1. Wait for the chamber temperature (green arrow) to fall below 100 degrees Centigrade.2. Before unsealing the door, push the red ON/OFF button to pop it out to the OFF position.3. Use gloves when opening the autoclave door.4. Unseal the door slowly. If the locking wheel won't turn, get help -never use excessive force to spin the wheel.5. Open the door slowly, just acrack at first. Keep head and body well behind the door, using it as ashield against any escaping steam.6. When no more escaping steam is visible, step back and slowly swing the door fully open.7. Unload the chamber and inspect for spills. If there is aspill you are responsible for cleanup -contact Michael Mason for help. Do not attempt to clean the chamber with the jacket pressurized (hot chamber walls). Post awarning note to prevent further use until cleaning is complete.SAFETY TIPS1. Use containment trays for all materials to be autoclaved.2. Never autoclave tightly sealed containers.3. Check the red ON/OFF button before either closing or opening the chamber door. It should be out -in the OFF position.4. Use gloves when opening the chamber door and when loading/unloading the chamber.5. Avoid exposure to steam when opening the chamber door at the end of arun. Open the door slowly, and use it as ashield.Main specification1000Liter steam /electric heating retort sterilizer specificationmodeDN900scopepressure containerTypeDouble vessel sterilizer water spraypot sizeΦ900*1500mmChamber capacity1.1m3design temperature143 0Coperating temperature≤138 0Cdesign pressure0.3MPaworking pressure≤0.16Mpaworking mediumWater /steam /compressed airmaterialSUS304 welding coefficient0.7corrosion allowance1mmSteam inlet diameterDN40-50Exhaust diameterDN32-40cold and hot water connection tube diameterDN40-50Overflow pipe diameterDN25-50drain-pipe diameterDN40-50Relief valve diameterDN25-50Compressed air diameterDN15-20Adjust mouth diameterDN25-40thickness6mmweight700kgoverall dimension L*W*H2200*1450*1432Total pricewith all accessories**,300usd FOB NINGBOThe above table is for basic specification to help you get an overview of the retort we offer to you.Here below are some accessories comes with this deviceNo.Itemdescription1Steam boilerStainless steel2Pipes and valvesAll the needed pipes and valves3Sterilization basketsSize see the flowing spec4Pumpcirculating pump used to transfer cool water and collect hot water5Control panelControl the temperature, pump and pressure6Safety lock deviceSafety device ,ensure safety work environment7alarm lampRed yellow green8Temperature gaugeAccording to standard design9Pressure gaugeAccording to standard designHere are the size of the sterilization basketsBaskets No.Baskets materialBaskets size2Stainless steel750×650×530mmSterilization baskets can be designed as your requestYou need to prepare the following device:1.Water tank not less than 2T capacity2.A suitable place to install this device.about installationWe will offer you the related help to teach you how to install and operate this machine. If needed ,we can send the expert to your work place to install and training your staff.CertificateWe have passed CE and ISO 9001:2000. To insure the top quality, all the equipment before they leave the factory are to pass strict inspection.WarrantyWe offer 1years warranty, in this warranty time, we take responsibly to all the problem that happened on this device.After this warranty time, we offer related service inmaintenance.Required parts only charge the cost,do not add any profit.Our service time7days one week, 16 hours aday, this will insure customers from every side of the world can get atimely service when need.